Metal Roofing Trim & Siding Trim

Let's Build Something Together

Get a Metal Roofing Estimate

Metal roofing trim comes in every style and color that we offer. We also can make almost any custom trim that you may need for your project.

Installation of Metal Roofing Trim


Metal Roofing Trim - Ridge Cap Profile

Ridge Cap – Metal Roofing Trim

Ridge caps are used on top of your ridge line or hip of the roof. So, the Ridgecap sitting on top of the rib allows adequate space for ventilation when used with a ventilated closure strip.


Metal Roofing Trim - Valley Profile

Valley – Metal Roofing Trim

Valleys are used in a valley that’s created by two intersecting slopes. Your Valley has a raised section at the low point to prevent water from traveling up the opposite slope. You should install this valley prior to any panels in the valley area.


Metal Roofing Trim - Small Outside Corner

Small Outside Corner – Metal Roofing Trim

These are used on the gable end or as the outside corner when panels are used as siding for a building. The Small Outside Corner has a built in drop enabling it to cover a 3/4″ rib.


Metal Roofing Trim - Rake Edge

Rake Edge – Metal Roofing Trim

A rake edge is used on the gable end of the roof. The Rake Edge has a built in drop enabling it to cover a 3/4″ rib.


Metal Roofing Trim - Pitch Transition

Pitch Transition – Metal Roofing Trim

When transitioning from a higher slope to a lower slope a pitch transition is installed under the upper slope panel and on top of the lower slope panel. The lower portion of the Transition rests on top of the lower panel ribs and should be installed with outer closures to ensure water tightness.


Metal Roofing Trim - Endwall

Endwall – Metal Roofing Trim

This metal roofing trim is used when a panel intersects a wall perpendicularly. The Endwall will install up the vertical wall and on top of the panel. The Endwall should be installed under any removable siding or attached and caulked to brick or stone. The lower portion of the Endwall rests on top of the lower panel ribs and should be installed with outer closures to ensure water tightness.


Metal Roofing Trim - Sidewall

Sidewall – Metal Roofing Trim

Sidewalls are used when panels run parallel to a vertical wall. The Sidewall will install up the vertical wall and on top of the panel. The upper portion of the Sidewall should be installed under any removable siding or attached and caulked to brick or stone. The Sidewall has a built in drop enabling it to cover a 3/4″ rib.


Metal Roofing Trim - Drip Edge

Drip Edge – Metal Roofing Trim

This Drip Edge is used at the lowest point of a roof slope. The Drip Edge is used to prevent water from full gutters from running back under the roofing material. The Drip Edge is installed under the panels and down into the gutter.


Metal Roofing Trim - Snow Guard Bar

Snow Guard Bar – Metal Roofing Trim

A Snow Guard Bar is installed near the lowest point of a roof slope. The Snow Guard is used to prevent ice and snow from sliding off metal roof panels. It catches snow and ice before reaching the gutters to allow a slow and even melt. Snow Guard is installed on top of the ribs above the outside wall of the structure.


Metal Roofing Trim - J-Channel

J-Channel – Metal Roofing Trim

J-Channels are used to trim around doors, windows, skylights, and other square or rectangular penetrations in roofing or siding panels.


Metal Roofing Trim - Base Guard

Base Guard – Metal Roofing Trim

This guard is used at the base of metal siding panels. The Base Guard installs underneath the panel and extends down onto the ground or concrete footer of the building effectively sealing it off.

Follow Us on our own Networks
Share on Facebook Follow us on Twitter Follow us on Google+ Subscribe to News Feed

I would appreciate your sharing this page on one of your Social Networks! Thanks so much! Bret Lyon

Pin It on Pinterest